NAND boot
F0: 102B 0000
FA: 1042 0000
FA: 1042 0000 [0200]
F9: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 0600 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [1000]
MK: 0000 0000 [0000]
T0: 0000 01AD [0101]
Jump to BL
NOTICE: BL2: v2.11.0(release):
NOTICE: BL2: Built : 11:21:00, Mar 8 2025
NOTICE: WDT: Cold boot
NOTICE: WDT: disabled
NOTICE: CPU: MT7988
NOTICE: EMI: DDR4 4BG mode
NOTICE: EMI: Using DDR unknown settings
NOTICE: EMI: Detected DRAM size: 8192 MB
NOTICE: EMI: complex R/W mem test passed
WARNING: CASN page check failed
WARNING: Fail to read CASN page. Try reading parameter page
NOTICE: SPI_NAND parses attributes from parameter page.
NOTICE: SPI_NAND Detected ID 0xef
NOTICE: Page size 2048, Block size 131072, size 268435456
NOTICE: Initializing NMBM ...
NOTICE: Signature found at block 2047 [0x0ffe0000]
NOTICE: First info table with writecount 0 found in block 1920
NOTICE: Second info table with writecount 0 found in block 1923
NOTICE: NMBM has been successfully attached in read-only mode
NOTICE: BL2: Booting BL31
NOTICE: BL31: v2.11.0(release):
NOTICE: BL31: Built : 11:21:04, Mar 8 2025
U-Boot 2024.10-rc2 (Mar 08 2025 - 11:10:17 +0800)
CPU: MediaTek MT7988
Model: mt7988-rfb
(mediatek,mt7988-spim-nand-rfb)
DRAM: 8 GiB
Core: 48 devices, 12 uclasses, devicetree: separate
Initializing NMBM ...
spi-nand: spi_nand spi_nand@0: CASN page check failed
spi-nand: spi_nand spi_nand@0: Fallback to read ID
spi-nand: spi_nand spi_nand@0: Winbond SPI NAND was found.
spi-nand: spi_nand spi_nand@0: 256 MiB, block size: 128 KiB, page size: 2048, OOB size: 128
Could not find a valid device for nmbm0
Signature found at block 2047 [0x0ffe0000]
First info table with writecount 0 found in block 1920
Second info table with writecount 0 found in block 1923
NMBM has been successfully attached
Loading Environment from MTD... *** Warning - bad CRC, using default environment
In: serial@11000000
Out: serial@11000000
Err: serial@11000000
Net:
Warning: ethernet@15100000 (eth0) using random MAC address - 3a:9e:e6:63:dd:de
eth0: ethernet@15100000
*** U-Boot Boot Menu ***
1. Startup system (Default)
2. Upgrade firmware
3. Upgrade ATF BL2
4. Upgrade ATF FIP
5. Upgrade ATF BL31 only
6. Upgrade bootloader only
7. Upgrade single image
8. Load image
9. Start Web failsafe
0. U-Boot console
Press UP/DOWN to move, ENTER to select, ESC to quit
ubi0: attaching mtd6
ubi0: scanning is finished
ubi0: attached mtd6 (name "ubi", size 112 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 900, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 3/0, WL threshold: 4096, image sequence number: 1717567889
ubi0: available PEBs: 0, total reserved PEBs: 900, PEBs reserved for bad PEB handling: 38
Volume firmware not found!
No size specified -> Using max size (4190208)
Read 4190208 bytes from volume kernel to 0000000044000000
## Loading kernel from FIT Image at 44000000 ...
Using 'config-1' configuration
Trying 'kernel-1' kernel subimage
Description: ARM64 OpenWrt Linux-5.4.271
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x440000e8
Data Size: 4079828 Bytes = 3.9 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x48080000
Entry Point: 0x48080000
Hash algo: crc32
Hash value: 66074b12
Hash algo: sha1
Hash value: 9e960a57792a18b1218da2e9808060d1336fa155
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 44000000 ...
Using 'config-1' configuration
Trying 'fdt-1' fdt subimage
Description: ARM64 OpenWrt BPI-R4-NAND device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x443e42f8
Data Size: 35220 Bytes = 34.4 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: f38f6e07
Hash algo: sha1
Hash value: 70587200d406deca7988ece4511e85aa3a1407ec
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x443e42f8
Working FDT set to 443e42f8
Uncompressing Kernel Image to 48080000
Loading Device Tree to 00000000ff7ea000, end 00000000ff7f5993 ... OK
Working FDT set to ff7ea000
Add 'ramoops@42ff0000' node failed: FDT_ERR_EXISTS
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x411fd090]
[ 0.000000] Linux version 5.4.271 (linux@Ubuntu18.04.2-Devel) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 unknown)) #0 SMP Wed Jun 5 06:11:29 2024
[ 0.000000] Machine model: Bananapi BPI-R4
[ 0.000000] earlycon: uart8250 at MMIO32 0x0000000011000000 (options '')
[ 0.000000] printk: bootconsole [uart8250] enabled
[ 0.000000] On node 0 totalpages: 2094272
[ 0.000000] DMA32 zone: 12288 pages used for memmap
[ 0.000000] DMA32 zone: 0 pages reserved
[ 0.000000] DMA32 zone: 783552 pages, LIFO batch:63
[ 0.000000] Normal zone: 20480 pages used for memmap
[ 0.000000] Normal zone: 1310720 pages, LIFO batch:63
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
[ 0.000000] percpu: Embedded 20 pages/cpu s44376 r8192 d29352 u81920
[ 0.000000] pcpu-alloc: s44376 r8192 d29352 u81920 alloc=20*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[ 0.000000] CPU features: detected: Spectre-BHB
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 2061504
[ 0.000000] Kernel command line: console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11000000 pci=pcie_bus_perf
[ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: mapped [mem 0xfb7ea000-0xff7ea000] (64MB)
[ 0.000000] Memory: 8138456K/8377088K available (8382K kernel code, 602K rwdata, 2468K rodata, 512K init, 293K bss, 238632K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: CONFIG_RCU_FANOUT set to non-default value of 32.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 416 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] GICv3: 16 PPIs implemented
[ 0.000000] GICv3: no VLPI support, no direct LPI support
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000
[ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns
[ 0.000003] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns
[ 0.008268] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=52000)
[ 0.018660] pid_max: default: 32768 minimum: 301
[ 0.023397] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.031077] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.039784] ASID allocator initialised with 65536 entries
[ 0.045292] rcu: Hierarchical SRCU implementation.
[ 0.050392] smp: Bringing up secondary CPUs ...
[ 0.055180] Detected VIPT I-cache on CPU1
[ 0.055198] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000
[ 0.055212] CPU1: Booted secondary processor 0x0000000001 [0x411fd090]
[ 0.055426] Detected VIPT I-cache on CPU2
[ 0.055435] GICv3: CPU2: found redistributor 2 region 0:0x000000000c0c0000
[ 0.055442] CPU2: Booted secondary processor 0x0000000002 [0x411fd090]
[ 0.055643] Detected VIPT I-cache on CPU3
[ 0.055652] GICv3: CPU3: found redistributor 3 region 0:0x000000000c0e0000
[ 0.055658] CPU3: Booted secondary processor 0x0000000003 [0x411fd090]
[ 0.055688] smp: Brought up 1 node, 4 CPUs
[ 0.112702] SMP: Total of 4 processors activated.
[ 0.117464] CPU features: detected: 32-bit EL0 Support
[ 0.122664] CPU features: detected: CRC32 instructions
[ 0.127950] CPU: All CPU(s) started at EL2
[ 0.132105] alternatives: patching kernel code
[ 0.139021] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.148907] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.155928] pinctrl core: initialized pinctrl subsystem
[ 0.161632] NET: Registered protocol family 16
[ 0.166314] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.173157] printk: console [pstore-1] enabled
[ 0.177696] pstore: Registered ramoops as persistent store backend
[ 0.183954] ramoops: using 0x10000@0x42ff0000, ecc: 0
[ 0.191785] GPIO line 432 (asm_sel) hogged as output/high
[ 0.197291] GPIO line 433 (pca9545_rst) hogged as output/high
[ 0.208046] cryptd: max_cpu_qlen set to 1000
[ 0.213610] SCSI subsystem initialized
[ 0.217508] libata version 3.00 loaded.
[ 0.221488] usbcore: registered new interface driver usbfs
[ 0.227125] usbcore: registered new interface driver hub
[ 0.232523] usbcore: registered new device driver usb
[ 0.238192] Bluetooth: Core ver 2.22
[ 0.241835] NET: Registered protocol family 31
[ 0.246331] Bluetooth: HCI device and connection manager initialized
[ 0.252768] Bluetooth: HCI socket layer initialized
[ 0.257704] Bluetooth: L2CAP socket layer initialized
[ 0.262819] Bluetooth: SCO socket layer initialized
[ 0.267960] rbus 18000000.wbsys: PCI host bridge to bus 0004:00
[ 0.273958] pci_bus 0004:00: root bus resource [mem 0x18000000-0x18ffffff]
[ 0.280917] pci_bus 0004:00: root bus resource [bus 00-ff]
[ 0.286469] pci_bus 0004:00: scanning bus
[ 0.290534] pci 0004:00:00.0: [14c3:7981] type 00 class 0x000280
[ 0.296625] pci 0004:00:00.0: reg 0x10: [mem 0x18000000-0x1800000f 64bit]
[ 0.303498] pci 0004:00:00.0: reg 0x18: [mem 0x00000000-0x0000000f]
[ 0.309842] pci 0004:00:00.0: reg 0x1c: [mem 0x00000000-0x0000000f]
[ 0.316186] pci 0004:00:00.0: reg 0x20: [mem 0x00000000-0x0000000f]
[ 0.322531] pci 0004:00:00.0: reg 0x24: [mem 0x00000000-0x0000000f]
[ 0.329789] pci_bus 0004:00: fixups for bus
[ 0.334025] pci_bus 0004:00: bus scan returning with max=00
[ 0.339841] clocksource: Switched to clocksource arch_sys_counter
[ 0.346370] thermal_sys: Registered thermal governor 'fair_share'
[ 0.346371] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.352544] thermal_sys: Registered thermal governor 'step_wise'
[ 0.358630] thermal_sys: Registered thermal governor 'user_space'
[ 0.364710] thermal_sys: Registered thermal governor 'power_allocator'
[ 0.371217] NET: Registered protocol family 2
[ 0.382440] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.392082] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear)
[ 0.400785] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.409009] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear)
[ 0.416903] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.423600] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear)
[ 0.430568] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear)
[ 0.438064] NET: Registered protocol family 1
[ 0.442504] PCI: CLS 0 bytes, default 64
[ 0.447073] workingset: timestamp_bits=46 max_order=21 bucket_order=0
[ 0.455490] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.461474] ntfs: driver 2.1.32 [Flags: R/W].
[ 0.465937] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.494228] Debug interface error
[ 0.497651] io scheduler mq-deadline registered
[ 0.502240] io scheduler kyber registered
[ 0.506358] io scheduler bfq registered
[ 0.510781] phy phy-usb-phy@11e10000.3: type_sw - reg 0x218, index 0
[ 0.517615] mtk-pcie 11300000.pcie: host bridge /pcie@11300000 ranges:
[ 0.524234] mtk-pcie 11300000.pcie: Parsing ranges property...
[ 0.530146] mtk-pcie 11300000.pcie: IO 0x30000000..0x301fffff -> 0x30000000
[ 0.537468] mtk-pcie 11300000.pcie: MEM 0x30200000..0x37ffffff -> 0x30200000
[ 0.544811] mtk-pcie 11300000.pcie: failed to get max link width
[ 0.671245] mtk-pcie 11300000.pcie: PCI host bridge to bus 0000:00
[ 0.677514] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.683071] pci_bus 0000:00: root bus resource [io 0x0000-0x1fffff] (bus address [0x30000000-0x301fffff])
[ 0.692854] pci_bus 0000:00: root bus resource [mem 0x30200000-0x37ffffff]
[ 0.699813] pci_bus 0000:00: scanning bus
[ 0.703886] pci 0000:00:00.0: [14c3:7988] type 01 class 0x060400
[ 0.709990] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit]
[ 0.716917] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
[ 0.723093] pci 0000:00:00.0: PME# disabled
[ 0.728286] pci_bus 0000:00: fixups for bus
[ 0.732527] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 0
[ 0.739311] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.747420] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 1
[ 0.754253] pci_bus 0000:01: scanning bus
[ 0.758324] pci 0000:01:00.0: [14c3:7990] type 00 class 0x028000
[ 0.764441] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit pref]
[ 0.771768] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00007fff 64bit]
[ 0.778742] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.784913] pci 0000:01:00.0: PME# disabled
[ 0.790015] pci_bus 0000:01: fixups for bus
[ 0.794249] pci_bus 0000:01: bus scan returning with max=01
[ 0.799890] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.806586] pci_bus 0000:00: bus scan returning with max=01
[ 0.812236] pci 0000:00:00.0: BAR 9: assigned [mem 0x30200000-0x303fffff 64bit pref]
[ 0.820077] pci 0000:00:00.0: BAR 8: assigned [mem 0x30400000-0x304fffff]
[ 0.826950] pci 0000:00:00.0: BAR 0: assigned [mem 0x30500000-0x30507fff 64bit]
[ 0.834356] pci 0000:01:00.0: BAR 0: assigned [mem 0x30200000-0x303fffff 64bit pref]
[ 0.842209] pci 0000:01:00.0: BAR 2: assigned [mem 0x30400000-0x30407fff 64bit]
[ 0.849619] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.854644] pci 0000:00:00.0: bridge window [mem 0x30400000-0x304fffff]
[ 0.861516] pci 0000:00:00.0: bridge window [mem 0x30200000-0x303fffff 64bit pref]
[ 0.869367] pci 0000:00:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
[ 0.877925] pci 0000:01:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
[ 0.886573] mtk-pcie 11310000.pcie: host bridge /pcie@11310000 ranges:
[ 0.893188] mtk-pcie 11310000.pcie: Parsing ranges property...
[ 0.899096] mtk-pcie 11310000.pcie: IO 0x38000000..0x381fffff -> 0x38000000
[ 0.906416] mtk-pcie 11310000.pcie: MEM 0x38200000..0x3fffffff -> 0x38200000
[ 0.913762] mtk-pcie 11310000.pcie: failed to get max link width
[ 1.043007] mtk-pcie 11310000.pcie: PCI host bridge to bus 0001:00
[ 1.049266] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 1.054826] pci_bus 0001:00: root bus resource [io 0x200000-0x3fffff] (bus address [0x38000000-0x381fffff])
[ 1.064778] pci_bus 0001:00: root bus resource [mem 0x38200000-0x3fffffff]
[ 1.071737] pci_bus 0001:00: scanning bus
[ 1.075804] pci 0001:00:00.0: [14c3:7988] type 01 class 0x060400
[ 1.081903] pci 0001:00:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit]
[ 1.088825] pci 0001:00:00.0: PME# supported from D0 D3hot D3cold
[ 1.094997] pci 0001:00:00.0: PME# disabled
[ 1.100127] pci_bus 0001:00: fixups for bus
[ 1.104362] pci 0001:00:00.0: scanning [bus 00-00] behind bridge, pass 0
[ 1.111146] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.119256] pci 0001:00:00.0: scanning [bus 00-00] behind bridge, pass 1
[ 1.126085] pci_bus 0001:01: scanning bus
[ 1.130157] pci 0001:01:00.0: [14c3:7991] type 00 class 0x028000
[ 1.136276] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit pref]
[ 1.143603] pci 0001:01:00.0: reg 0x18: [mem 0x00000000-0x00007fff 64bit]
[ 1.150576] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[ 1.156747] pci 0001:01:00.0: PME# disabled
[ 1.161835] pci_bus 0001:01: fixups for bus
[ 1.166068] pci_bus 0001:01: bus scan returning with max=01
[ 1.171709] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.178406] pci_bus 0001:00: bus scan returning with max=01
[ 1.184051] pci 0001:00:00.0: BAR 9: assigned [mem 0x38200000-0x383fffff 64bit pref]
[ 1.191894] pci 0001:00:00.0: BAR 8: assigned [mem 0x38400000-0x384fffff]
[ 1.198772] pci 0001:00:00.0: BAR 0: assigned [mem 0x38500000-0x38507fff 64bit]
[ 1.206182] pci 0001:01:00.0: BAR 0: assigned [mem 0x38200000-0x383fffff 64bit pref]
[ 1.214036] pci 0001:01:00.0: BAR 2: assigned [mem 0x38400000-0x38407fff 64bit]
[ 1.221445] pci 0001:00:00.0: PCI bridge to [bus 01]
[ 1.226472] pci 0001:00:00.0: bridge window [mem 0x38400000-0x384fffff]
[ 1.233344] pci 0001:00:00.0: bridge window [mem 0x38200000-0x383fffff 64bit pref]
[ 1.241194] pci 0001:00:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
[ 1.249756] pci 0001:01:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
[ 1.258392] mtk-pcie 11280000.pcie: host bridge /pcie@11280000 ranges:
[ 1.265006] mtk-pcie 11280000.pcie: Parsing ranges property...
[ 1.270913] mtk-pcie 11280000.pcie: IO 0x20000000..0x201fffff -> 0x20000000
[ 1.278232] mtk-pcie 11280000.pcie: MEM 0x20200000..0x27ffffff -> 0x20200000
[ 1.285559] mtk-xsphy usb-phy@11e10000: incompatible phy type
[ 1.291395] mtk-pcie 11280000.pcie: failed to get max link width
[ 1.503849] mtk-pcie 11280000.pcie: PCIe link down, ltssm reg val: 0x1
[ 1.510498] mtk-pcie: probe of 11280000.pcie failed with error -110
[ 1.516892] mtk-pcie 11290000.pcie: host bridge /pcie@11290000 ranges:
[ 1.523505] mtk-pcie 11290000.pcie: Parsing ranges property...
[ 1.529412] mtk-pcie 11290000.pcie: IO 0x28000000..0x281fffff -> 0x28000000
[ 1.536731] mtk-pcie 11290000.pcie: MEM 0x28200000..0x2fffffff -> 0x28200000
[ 1.544061] mtk-pcie 11290000.pcie: failed to get max link width
[ 1.755847] mtk-pcie 11290000.pcie: PCIe link down, ltssm reg val: 0x1
[ 1.762477] mtk-pcie: probe of 11290000.pcie failed with error -110
[ 1.769410] mtk-power-controller 11d10000.topmisc: /topmisc@11d10000/eth2p5@2: A default off power domain has been ON
[ 1.780311] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 1.787102] printk: console [ttyS0] disabled
[ 1.811544] 11000000.serial: ttyS0 at MMIO 0x11000000 (irq = 17, base_baud = 2500000) is a ST16650V2
[ 1.820813] printk: console [ttyS0] enabled
[ 1.820813] printk: console [ttyS0] enabled
[ 1.829173] printk: bootconsole [uart8250] disabled
[ 1.829173] printk: bootconsole [uart8250] disabled
[ 1.839349] mtk_rng trng@1020f000: registered RNG driver
[ 1.839388] random: crng init done
[ 1.849356] loop: module loaded
[ 1.854503] spi-nand spi0.0: calibration result: 0x2
[ 1.859561] spi-nand spi0.0: Winbond SPI NAND was found.
[ 1.864869] spi-nand spi0.0: 256 MiB, block size: 128 KiB, page size: 2048, OOB size: 128
[ 1.874522] mt7988-pinctrl 1001f000.pinctrl: invalid function mdio in map table
[ 1.882385] [mtk_hw_init] reset_lock:0, force:1
[ 1.887062] [mtk_hw_init] execute fe cold reset
[ 1.902592] mtk_soc_eth 15100000.ethernet: MDC is running on 8333333 Hz
[ 1.929820] mtk_soc_eth 15100000.ethernet: generated random MAC address 16:3a:b1:9b:51:e8
[ 1.938390] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc012080000, irq 14
[ 1.947473] mtk_soc_eth 15100000.ethernet: generated random MAC address 56:69:af:9e:88:51
[ 1.955987] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine at 0xffffffc012080000, irq 14
[ 1.965054] mtk_soc_eth 15100000.ethernet: generated random MAC address ce:fb:11:65:63:02
[ 1.973566] mtk_soc_eth 15100000.ethernet eth2: mediatek frame engine at 0xffffffc012080000, irq 14
[ 1.982604] (unnamed net_device) (dummy): netif_napi_add() called with weight 256
[ 1.990229] PPP generic driver version 2.4.2
[ 1.994535] PPP BSD Compression module registered
[ 1.999228] PPP Deflate Compression module registered
[ 2.004269] NET: Registered protocol family 24
[ 2.008737] usbcore: registered new interface driver r8152
[ 2.014220] usbcore: registered new interface driver ax88179_178a
[ 2.020312] usbcore: registered new interface driver cdc_ether
[ 2.026142] usbcore: registered new interface driver rndis_host
[ 2.032065] usbcore: registered new interface driver cdc_ncm
[ 2.037727] usbcore: registered new interface driver qmi_wwan_q
[ 2.043646] usbcore: registered new interface driver qmi_wwan
[ 2.049390] usbcore: registered new interface driver cdc_mbim
[ 2.055282] xhci-mtk 11200000.xhci: 11200000.xhci supply vbus not found, using dummy regulator
[ 2.063906] xhci-mtk 11200000.xhci: 11200000.xhci supply vusb33 not found, using dummy regulator
[ 2.072798] phy phy-usb-phy@11c50000.0: try to get sw efuse
[ 2.078365] phy phy-usb-phy@11c50000.1: try to get sw efuse
[ 2.084085] xhci-mtk 11200000.xhci: xHCI Host Controller
[ 2.089443] xhci-mtk 11200000.xhci: new USB bus registered, assigned bus number 1
[ 2.099966] xhci-mtk 11200000.xhci: hcc params 0x01403f99 hci version 0x110 quirks 0x0000000000210010
[ 2.109241] xhci-mtk 11200000.xhci: irq 122, io mem 0x11200000
[ 2.115119] xhci-mtk 11200000.xhci: xHCI Host Controller
[ 2.120425] xhci-mtk 11200000.xhci: new USB bus registered, assigned bus number 2
[ 2.127898] xhci-mtk 11200000.xhci: Host supports USB 3.2 Enhanced SuperSpeed
[ 2.135255] hub 1-0:1.0: USB hub found
[ 2.139015] hub 1-0:1.0: 1 port detected
[ 2.143106] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.151358] hub 2-0:1.0: USB hub found
[ 2.155114] hub 2-0:1.0: 1 port detected
[ 2.159224] usbcore: registered new interface driver cdc_wdm
[ 2.164942] usbcore: registered new interface driver uas
[ 2.170274] usbcore: registered new interface driver usb-storage
[ 2.176307] usbcore: registered new interface driver usbserial_generic
[ 2.182830] usbserial: USB Serial support registered for generic
[ 2.188838] usbcore: registered new interface driver option
[ 2.194406] usbserial: USB Serial support registered for GSM modem (1-port)
[ 2.201406] usbcore: registered new interface driver pl2303
[ 2.206973] usbserial: USB Serial support registered for pl2303
[ 2.212893] usbcore: registered new interface driver qcaux
[ 2.218373] usbserial: USB Serial support registered for qcaux
[ 2.224207] usbcore: registered new interface driver qcserial
[ 2.229949] usbserial: USB Serial support registered for Qualcomm USB modem
[ 2.237030] i2c /dev entries driver
[ 2.248236] vcore: supplied by rt5190a-buck1
[ 2.255198] proc: supplied by rt5190a-buck1
[ 2.261651] rt5190a-buck4: supplied by rt5190a-buck1
[ 2.267558] rt5190a-ldo: supplied by regulator-dummy
[ 2.274726] at24 3-0057: 256 byte 24c02 EEPROM, writable, 1 bytes/write
[ 2.283248] rtc-pcf8563 3-0051: low voltage detected, date/time is not reliable.
[ 2.290670] rtc-pcf8563 3-0051: registered as rtc0
[ 2.296334] i2c i2c-2: Added multiplexed i2c bus 3
[ 2.301170] i2c i2c-2: Added multiplexed i2c bus 4
[ 2.306002] i2c i2c-2: Added multiplexed i2c bus 5
[ 2.311614] at24 6-0051: 256 byte 24c02 EEPROM, writable, 1 bytes/write
[ 2.318770] at24 6-0052: 256 byte 24c02 EEPROM, writable, 1 bytes/write
[ 2.325393] i2c i2c-2: Added multiplexed i2c bus 6
[ 2.330179] pca954x 2-0070: registered 4 multiplexed busses for I2C switch pca9545
[ 2.338088] mtk-soc-temp-lvts 1100a000.lvts: [lvts_cal] golden_temp = 60
[ 2.344784] mtk-soc-temp-lvts 1100a000.lvts: [lvts_cal] num:g_count:g_count_rc 0:19474:5445 1:19473:0 2:19474:0 3:19466:0 4:19536:5451 5:19575:0 6:19527:0 7:19574:0
[ 2.361362] mtk-soc-temp-lvts 1100a000.lvts: [COUNT_RC_NOW] 0:5449 1:5445 2:5444 3:5445 4:5459 5:5454 6:5455 7:5456
[ 2.371895] mtk-soc-temp-lvts 1100a000.lvts: set_polling_speed 0, LVTSMONCTL1_0= 0x10000c,LVTSMONCTL2_0= 0x10001
[ 2.382056] mtk-soc-temp-lvts 1100a000.lvts: set_hw_filter 0, LVTSMSRCTL0_0= 0xb6d
[ 2.389613] mtk-soc-temp-lvts 1100a000.lvts: lvts0: read all 4 sensors in 10080 us, one in 2404 us
[ 2.398577] mtk-soc-temp-lvts 1100a000.lvts: set_polling_speed 1, LVTSMONCTL1_0= 0x10000c,LVTSMONCTL2_0= 0x10001
[ 2.408737] mtk-soc-temp-lvts 1100a000.lvts: set_hw_filter 1, LVTSMSRCTL0_0= 0xb6d
[ 2.416301] mtk-soc-temp-lvts 1100a000.lvts: lvts1: read all 4 sensors in 10080 us, one in 2404 us
[ 2.425253] mtk-soc-temp-lvts 1100a000.lvts: set_tc_hw_reboot_threshold: LVTS0, the dominator sensing point= 0
[ 2.435241] mtk-soc-temp-lvts 1100a000.lvts: set_tc_hw_reboot_threshold: LVTS1, the dominator sensing point= 0
[ 2.445515] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com
[ 2.453992] Bluetooth: HCI UART driver ver 2.3
[ 2.458430] Bluetooth: HCI UART protocol H4 registered
[ 2.463557] Bluetooth: HCI UART protocol BCSP registered
[ 2.468895] Bluetooth: HCI UART protocol Broadcom registered
[ 2.474550] Bluetooth: HCI UART protocol QCA registered
[ 2.506017] exFAT: Version 1.3.0
[ 2.509779] Initializing XFRM netlink socket
[ 2.514207] NET: Registered protocol family 10
[ 2.519052] Segment Routing with IPv6
[ 2.522756] NET: Registered protocol family 17
[ 2.527213] Bridge firewalling registered
[ 2.531262] 8021q: 802.1Q VLAN Support v1.8
[ 2.543261] nmbm nmbm_spim_nand: Signature found at block 2047 [0x0ffe0000]
[ 2.543985] usb 2-1: new SuperSpeed Gen 1x2 USB device number 2 using xhci-mtk
[ 2.551150] nmbm nmbm_spim_nand: First info table with writecount 0 found in block 1920
[ 2.568117] nmbm nmbm_spim_nand: Second info table with writecount 0 found in block 1923
[ 2.576201] nmbm nmbm_spim_nand: NMBM has been successfully attached
[ 2.578399] hub 2-1:1.0: USB hub found
[ 2.582653] 5 fixed-partitions partitions found on MTD device nmbm_spim_nand
[ 2.586564] hub 2-1:1.0: 4 ports detected
[ 2.593405] Creating 5 MTD partitions on "nmbm_spim_nand":
[ 2.602875] 0x000000000000-0x000000100000 : "BL2"
[ 2.605713] mtk-msdc 11230000.mmc: phase: [map:7ffffff] [maxlen:27] [final:9]
[ 2.607934] 0x000000100000-0x000000180000 : "u-boot-env"
[ 2.615113] mmc0: new HS400 MMC card at address 0001
[ 2.620217] 0x000000180000-0x000000580000 : "Factory"
[ 2.625400] mmcblk0: mmc0:0001 8GTF4R 7.28 GiB
[ 2.630324] 0x000000580000-0x000000780000 : "FIP"
[ 2.634901] mmcblk0boot0: mmc0:0001 8GTF4R partition 1 4.00 MiB
[ 2.639563] 0x000000780000-0x000007800000 : "ubi"
[ 2.645512] mmcblk0boot1: mmc0:0001 8GTF4R partition 2 4.00 MiB
[ 2.650482] sfp sfp@0: Host maximum power 3.0W
[ 2.655803] mmcblk0rpmb: mmc0:0001 8GTF4R partition 3 512 KiB, chardev (247:0)
[ 2.660221] sfp sfp@0: tx disable 1 -> 1
[ 2.669024] GPT:Primary header thinks Alt. header is not at the end of the disk.
[ 2.671513] sfp sfp@0: SM: enter empty:detached:down event dev_attach
[ 2.678726] GPT:1 != 15269887
[ 2.685141] sfp sfp@0: SM: exit empty:down:down
[ 2.688094] GPT:Alternate GPT header not at the end of the disk.
[ 2.692808] sfp sfp@1: Host maximum power 3.0W
[ 2.698603] GPT:1 != 15269887
[ 2.698605] GPT: Use GNU Parted to correct GPT errors.
[ 2.703049] sfp sfp@1: tx disable 1 -> 1
[ 2.706012] mmcblk0: p1 p2 p3 p4 p5
[ 2.707848] usb 1-1: new high-speed USB device number 2 using xhci-mtk
[ 2.711275] sfp sfp@1: SM: enter empty:detached:down event dev_attach
[ 2.731558] sfp sfp@1: SM: exit empty:down:down
[ 2.862102] hub 1-1:1.0: USB hub found
[ 2.866032] hub 1-1:1.0: 5 ports detected
[ 3.547845] usb 1-1.5: new high-speed USB device number 3 using xhci-mtk
[ 3.688317] MediaTek MT7988 PHY dsa-0.0:00: TX-VCM SW cal result: 0x1
[ 3.713785] MediaTek MT7988 PHY dsa-0.0:01: TX-VCM SW cal result: 0x2
[ 3.739786] MediaTek MT7988 PHY dsa-0.0:02: TX-VCM SW cal result: 0x2
[ 3.766701] MediaTek MT7988 PHY dsa-0.0:03: TX-VCM SW cal result: 0x1
[ 3.785484] mt7530 mdio-bus:1f lan0 (uninitialized): PHY [dsa-0.0:00] driver [MediaTek MT7988 PHY]
[ 3.805596] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:01] driver [MediaTek MT7988 PHY]
[ 3.825630] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:02] driver [MediaTek MT7988 PHY]
[ 3.845643] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [dsa-0.0:03] driver [MediaTek MT7988 PHY]
[ 3.854788] mt7530 mdio-bus:1f: configuring for fixed/10gbase-kr link mode
[ 3.861667] DSA: tree 0 setup
[ 3.861671] mt7530 mdio-bus:1f: Link is Up - 10Gbps/Full - flow control rx/tx
[ 3.864627] mt7530-nl: genl_register_family_with_ops
[ 3.877146] UBI: auto-attach mtd5
[ 3.880463] ubi0: attaching mtd5
[ 4.139465] ubi0: scanning is finished
[ 4.146813] ubi0: attached mtd5 (name "ubi", size 112 MiB)
[ 4.152292] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 4.159154] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 4.165929] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 4.172876] ubi0: good PEBs: 900, bad PEBs: 0, corrupted PEBs: 0
[ 4.178869] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 4.186078] ubi0: max/mean erase counter: 3/0, WL threshold: 4096, image sequence number: 1717567889
[ 4.195195] ubi0: available PEBs: 0, total reserved PEBs: 900, PEBs reserved for bad PEB handling: 38
[ 4.204403] ubi0: background thread "ubi_bgt0d" started, PID 1037
[ 4.210985] block ubiblock0_1: created from ubi0:1(rootfs)
[ 4.216465] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[ 4.224862] rtc-pcf8563 3-0051: low voltage detected, date/time is not reliable.
[ 4.232247] rtc-pcf8563 3-0051: hctosys: unable to read the hardware clock
[ 4.242807] VFS: Mounted root (squashfs filesystem) readonly on device 253:0.
[ 4.250045] Freeing unused kernel memory: 512K
[ 4.275876] Run /sbin/init as init process
[ 4.421060] init: Console is alive
[ 4.966827] kmodloader: loading kernel modules from /etc/modules-boot.d/*